Welcome back for more Christmas in July!! I must have Christmas cookies on the brain!
This is a sneak peak at some of the new Christmas products being offered starting August 3rd.
- Basic Card Base - Cinnamon Cider Cardstock 8 1/2" X 5 1/2" scored at 4 1/4" and folded in half
- The largest of the Scalloped Contours Dies in Basic White Cardstock
- One of the cute prints from the Gingerbread & Peppermint DSP pack - cut to 3 1/2" X 4 3/4"
- I added a strip of White Glittered Organdy Ribbon across the base of the DSP before I adhered it
- A Basic White Cardstock scalloped square from the Layering Square Dies
- The gingerbread snowflake cut with the Gingerbread Dies and popped up with Dimensionals
- The sentiment is done with White Embossing powder and just cut to approx. 2 3/8" X 5/8"
- I added a bow with the same white glittery ribbon using a glue dot
- I brushed the cookie snow flake with Wink of Stella to give it a shimmery look
- Card base is Basic Red Cardstock 8 1/2" X 5 1/2" scored at 4 1/4" and folded in half
- Cut 1 1/4" X 5 1/2" strip off of the front of the card base down the right side
- Plaid DSP Layer on front is 2 3/4" X 5 1/4"
- Polk- a-dot DSP layer on inside back is 1 1/4" X 5 1/4"
- Scalloped rectangle in Basic White is from the Scalloped Contour Dies
- the stripe DSP is 2 3/4" X 4"
- Just make sure you do not put glue on the side of the back of the white rectangle that hangs over your card base!!
- Cookies and Peppermints are cut from the DSP with the Gingerbread Dies- I popped put the cookies with Dimensionals
- The sentiment is from the new Classic Cloche stamp set done with White Embossing Powder on Basic Red card stock and I clipped the ends for a banner look
- Card base is Basic Red Cardstock 8 1/2" X 5 1/2" scored at 4 1/4" and folded in half
- the diagonal stripe DSP is 4" x 5 1/4"
- The back of my jar is a piece of Smokey Slate cardstock approx 2" X 3" stamped with the jar from the Jar of Flowers stamp set with black ink.
- I cut 5 small and 4 medium white base and red peppermint swirls from cardstock with the Gingerbread dies and glued the pieces together to make my peppermints.
- I glued 3 down to the stamped jar and left the rest loose - piling them up in the middle of the jar while I pealed of the layer to expose the tape on the Mason Jar Shaker Dome - then stuck the dome over the top of all of the peppermints- lining up the edges of the dome with the stamped image of the jar.
- I added a piece of the red stitched ribbon from Playful Pets Trim Combo Pack across the rim of the jar -The shaker dome has a sticky layer on the top side as well - so I pulled off the layer to expose the sticky -and stuck it down.
- The peppermint swirled DSP is cut from the Scalloped Contour Dies then punched with the Jar Punc and placed the DSP over and around the jar - hiding all of the grey around the edges - You may need to trim those back before you stick your DSP down for good.
- The sentiment is cut from Basic Red with the Ornate Frames Die and embossed with White Embossing Powder and popped it up with Dimensionals.
- I tied a bow with the ribbon and attached it with a glue dot onto the ribbon going around the jar top
No comments:
Post a Comment